Fence na.conf
Node Assassin :: Fence na.conf |
This is the common Node Assassin configuration file that exists in /etc/na/. It must be updated to match your setup in order for your Node Assassin to work properly.
- Download the source code.
# This is the main configuration file for the Node Assassin fence device.
#
# This can support one or more fence devices.
#
# Node Assassin - Fence Agent
# Digimer; digimer@alteeve.com
# Apr. 08, 2010
# Version: 1.1.4
###############################################################################
# System: #
# - Here you setup general values for the fence agent and any/all nodes. #
###############################################################################
# This must be set to the number of Node Assassin devices you are using. It
# must be a positive integer.
#system::na_num = 1
system::na_num = 1
# Version of the fence_na fence agent.
system::agent_version = 1.1.4
# This is the log file. If unset, no logging will occur. If using '/var/log/',
# be sure that this agent is able to create or edit the file. The default is to
# write to '/tmp' to prevent accidental failure of the agent due to
# misconfiguration.
#system::log = /var/log/fence_na.log
system::log = /tmp/fence_na.log
# If set to '1', messages to STDOUT will be surpressed except in the event of
# errors. This can be overridden at the command line with the '-q' switch.
system::quiet = 0
# Set this to '1' to enable extra debug information. Ignored if 'system::quiet'
# is set.
system::debug = 0
# This is the authentication information... It is currently a simple plain text
# compare, but this will change prior to first release.
system::username = motoko
system::password = secret
###############################################################################
# Devices: #
# - Here you setup each fence device. There must be a corresponding #
# 'node::X::var' for each node where 'X' is between 1 and 'system::na_num'. #
###############################################################################
### Define values for Node 1.
# The nodes name. This must match exactly with the name set in the given node.
na::1::na_name = Motoko
# This is the IP address and port where I will connect to this node at.
# NOTE: THIS MUST MATCH THE VALUE USED IN '/etc/cluster.conf'! If you used a
# resolvable name there, use the same name here. Vice versa for IP addresses.
# If this doesn't match the 'ipaddr' argument sent by the 'fenced' daemon the
# fence will not work properly!
na::1::ipaddr = motoko.alteeve.com
na::1::tcp_port = 238
# This is the number of nodes supported by this Node Assassin
# (1 node = 2 ports; odd # = reset, even # = power)
na::1::max_nodes = 4
# These values are set when the node assassin program switch is run.
# NOT YET IMPLEMENTED.
na::1::mac = 02:00:00:FF:F0:AA
na::1::netmask = 255.255.255.0
na::1::gateway = 192.168.1.1
# These are aliases for each Node Assassin port. They should match the name or
# URI of the node connected to the given port. This is optional but will make
# the fenced 'list' argument more accurate and sane. If a port is listed here,
# then the 'list' action will return '<node_id>,<value>'. If a port is not
# defined, 'list' will return '<node_id>,<node::X::name-node_id>'. If a port is
# set to 'unused', it will be skipped when replying to a 'list'.
na::1::alias::1 = an_node01.alteeve.com
na::1::alias::2 = an_node02.alteeve.com
na::1::alias::3 = unused
na::1::alias::4 = unused
Input, advice, complaints and meanderings all welcome! | ||||
Digimer | digimer@alteeve.ca | https://alteeve.ca/w | legal stuff: | |
All info is provided "As-Is". Do not use anything here unless you are willing and able to take resposibility for your own actions. © 1997-2013 | ||||
Naming credits go to Christopher Olah! | ||||
In memory of Kettle, Tonia, Josh, Leah and Harvey. In special memory of Hannah, Jack and Riley. |