NA v1.1.4 Protoshield Variant: Difference between revisions

From Alteeve Wiki
Jump to navigation Jump to search
← Older editNewer edit →
Line 22: Line 22:
= Diagrams =
= Diagrams =


[[Image:na_v1.1.4_protoshield_layout_bicolour_LED.png|thumb|400px|left|Four-port Node Assassin v1.1.4, Protoshield variant board layout. Yes, it's pretty crappy, but it gets the idea across. Most of the wiring, resistors and diodes will need to share pin underneath the PCB.]][[Image:na_v1.1.4_protoshield_layout_single_colour_LED.png|thumb|400px|right|Same design, a little uglier, using normal LEDs.]]
[[Image:na_v1.1.4_protoshield_layout_single_colour_LED.png|thumb|400px|left|Same design, a little uglier, using normal LEDs.]]
[[Image:na_v1.1.4_protoshield_layout_single_colour_LED_with_wiring.png|thumb|400px|right|Wiring diagram. (See below for The GIMP formatted XCF with layers)]]
[[Media:na_v1.1.4_protoshield_layout_single_colour_LED_with_wiring.xcf]]
 
[[Image:na_v1.1.4_protoshield_layout_bicolour_LED.png|thumb|400px|left|Four-port Node Assassin v1.1.4, Protoshield variant board layout. Yes, it's pretty crappy, but it gets the idea across. Most of the wiring, resistors and diodes will need to share pin underneath the PCB.]]


[[Image:na_v1.1.4_circuit_diagram_protoshield_variant.png|thumb|900px|center|Circuit diagram for the four-port Node Assassin v1.1.4, Protoshield variant.]]
[[Image:na_v1.1.4_circuit_diagram_protoshield_variant.png|thumb|900px|center|Circuit diagram for the four-port Node Assassin v1.1.4, Protoshield variant.]]


{{na_footer}}
{{na_footer}}

Revision as of 02:25, 21 March 2010

 Node Assassin :: NA v1.1.4 Protoshield Variant

This version of the Node Assassin hardware is designed to fit on the Arduino Protoshield v.4. It's a little cramped, but it fits.

Part List

Choice:

  • 4x LEDs: 350-1839-ND (Bicolor Red/Green, 2x1 stack, common cathode)
  • 4x LEDs: Std. small 10mA Green LEDs

Or:

  • 4x LEDs: Std. small 10mA Green LEDs
  • 4x LEDs: Std. small 10mA Yellow LEDs
  • 4x LEDs: Std. small 10mA Red LEDs

Diagrams

Same design, a little uglier, using normal LEDs.
Wiring diagram. (See below for The GIMP formatted XCF with layers)

Media:na_v1.1.4_protoshield_layout_single_colour_LED_with_wiring.xcf

Four-port Node Assassin v1.1.4, Protoshield variant board layout. Yes, it's pretty crappy, but it gets the idea across. Most of the wiring, resistors and diodes will need to share pin underneath the PCB.
Circuit diagram for the four-port Node Assassin v1.1.4, Protoshield variant.

 

Input, advice, complaints and meanderings all welcome!
Digimer digimer@alteeve.ca https://alteeve.ca/w legal stuff:  
All info is provided "As-Is". Do not use anything here unless you are willing and able to take resposibility for your own actions. © 1997-2013
Naming credits go to Christopher Olah!
In memory of Kettle, Tonia, Josh, Leah and Harvey. In special memory of Hannah, Jack and Riley.
Retrieved from ‘https://alteeve.com/w/index.php?title=NA_v1.1.4_Protoshield_Variant&oldid=1117’